DIGIMOD 1000

Two channels class D power amplifier with supply type switching, protected from excessive overheating and short-circuits. Power capability on 4 ohms 2 x 500W, on 8 ohms 2 x 260W, in bridged on 8 ohms 1000W RMS. 32dB gain, slew rate (8 ohm) 50V/µs, signal to noise ratio 105dB/A, distortion <0.5 (THD, DIM, SMPTE), 10 k ohm impedance electronically balanced audio input, damping factor at 500Hz on 8 ohm >500, bandwidth 10Hz- 30kHz. AC power voltage range 230V (115V) +/- 10% 1.6A (3.2A). Weight 2.42 lbs, overall dimensions 8.5”x 4.8”x 2”.
This model of power amplifier together with the DSP card opportunely programmed is used for the followings models of loudspeakers:
FR12, FR15, FR12-2 (x1), SW15 in bridge, SW18 in bridge, M12C in bridge with passive crossover, M15C in bridge with passive crossover.

DIGIMOD 1000 NPS

Two channels class D power amplifier with supply type switching, protected from excessive overheating and short-circuits. It can be fed through an opportune cable, connected to a Digimod 500 or Digimod 1000. Power capability on 4 ohm 2 x 410W, on 8 ohm 2 x 250W, in bridged on 8 ohm 820W RMS. 32dB gain, slew rate (8 ohm) 50V/µs, signal to noise ratio 105dB/A, distortion <0.5 (THD, DIM, SMPTE), 10 k ohm impedance electronically balanced audio input, damping factor at 500Hz on 8 ohm >500, bandwidth 10Hz- 30kHz. AC power voltage range 230V (115V) +/- 10% 2.2A (3.6A). Weight 1.3 lbs, overall dimensions 5.7 ”x 4.8”x 2”.

DIGIMOD 500

One channels class D power amplifier with supply type switching, protected from excessive overheating and short-circuits. Power capability on 4 ohm 530W, on 8 ohm 280W RMS. 32dB gain, slew rate (8 ohm) 50V/µs, signal to noise ratio 105dB/A, distortion <0.5 (THD, DIM, SMPTE), 10 k ohm impedance electronically balanced audio input, damping factor at 500Hz on 8 ohm >500, bandwidth 10Hz- 30kHz. AC power voltage range 230V (115V) +/- 10% 1.0A (2.0A). Weight 2.2 lbs, overall dimensions 8.5”x 4.8”x 2”.
This model of power amplifier together with the DSP card opportunely programmed is used for the followings models of loudspeakers:
FR12-2 (x1).

DIGIMOD 1500

Two channels class D power amplifier with supply type switching, protected from excessive overheating and short-circuits. Power capability on 4 ohm 2 x 750W, on 8 ohm 2 x 370W, in bridged on 8 ohm 1500W RMS. 32dB gain, slew rate (8 ohm) 50V/µs, signal to noise ratio 105dB/A, distortion <0.5 (THD, DIM, SMPTE), 10 k ohm impedance electronically balanced audio input, damping factor at 500Hz on 8 ohm >500, bandwidth 10Hz- 30kHz. AC power voltage range 230V (115V) +/- 10% 2.2A (3.6A). Weight 2.5 lbs, overall dimensions 8.5”x 4.8”x 2”.
This model of power amplifier together with the DSP card opportunely programmed is used for the followings models of loudspeakers:
SW21 in bridge.

DIGIMOD 2000HV

Two channels class D power amplifier with supply type switching, protected from excessive overheating and short-circuits. Power capability on 8 ohm 2 x 1050W, in bridged on 16 ohm 2100W RMS. 38dB gain, slew rate (8 ohm) 30V/µs, signal to noise ratio 105dB/A, distortion <0.5 (THD, DIM, SMPTE), 10 k ohm impedance electronically balanced audio input, damping factor at 500Hz on 8 ohm >100, bandwidth 10Hz- 30kHz. AC power voltage range 230V (115V) +/- 10% 2.9A (5.5A). Weight 2.5 lbs, overall dimensions 8.5”x 4.8”x 2”.
This model of power amplifier together with the DSP card opportunely programmed is used for the followings models of loudspeakers:
FR12HP, FR15HP, FR12-2HP (x1), SW18-2,SW15-2.

DIGIMOD 3000PFC

Equipped with Powersoft' last generation PFC power supply, capable of driving up to three 2-channel output stages and delivering up to 4000W, the DigiMod 3000PFC represents the ultimate solution for top level line arrays, high power subwoofer and high performance multi-channel applications.
Power Factor Correction (PFC): for worldwide operation and error proof connection to mains voltage (up to 400Vac tolerant)
Power output: 2x1700W on 4Ω in single ended mode, 1x3400W in bridge, total 4000W available for multi-channel applications
Thermal protections (Power limiting - Thermal shutdown)
Short-circuit/overload output protection
Clip limiter
Permanent signal limiter
High frequency protection
Auxiliary output voltage (±12V regulated, 350mA max)
Bypass line outputs for external active/passive filters
Mute command
Temperature controlled internal Fan and outputs (2 outputs on Power Amplifier, 1 output on power Supply)
This model of power amplifier together with the DSP card opportunely programmed is used for the followings models of loudspeakers:
LA12-2, subwoofer SW18-115 con woofer da 18".

DGMDSPA

The DSP-C is a 2in/4out processing board compatible with all DigiMod Series amp modules, that enables you to tailor the behavior of the amplifier through a precise 24bit/48kHz AD/DA conversion and 26 bit processing, to perfectly fit any application. The DSP-C is an incredibly open and flexible tool, allowing entering its powerful processing capabilities at different levels and with different approaches: With Analog Devices SigmaStudio™ software you will be free to build your own signal path choosing from a library of tens of different algorithms, from Linkwitz-Riley crossovers (up to 48dB/oct) to IIR and FIR filters, RMS and peak limiters and delay for speaker alignment. Four different presets can be stored on the DSP-C, allowing for easy selection of desired processing setting by end user, even when no network or remote control are available.